> gyro

MKS GY-292 gyroscope operation &amp instructions The following is an independently rewritten manual for the MKS GY-292 Gyro Very small gyro. nice price for the quality! Easy setup like Futaba 401.Good gyro for Novice rc helicopter pilot. Dual-rate remote to switch control function Input VoltageFDC 4.2 ~ 7.2 V Current ConsumptionF33 mA SizeF20 x 20 x 10.5 mm WeightF7 g External VR1(GAIN) switch set brake(delay control function ) External VR2(REV) set REV(reverse) function Specification&#65 306 &#9678 Input Voltage&#65306DC 4.2 ? 7.2 V &#9678 Current Consumption&#6530 633 mA &#9678 Operation Temperature&#6530 6-5&#8451 to 60&#8451 &#9678 Dimension&#653062 0 x 20 x 10.5 mm &#9678 Weight&#653067 g Gyro Function&#65306 &#9678 Dual-rate Adjust Mode : Heading Hold/Head Lock and Standard/Rate Mode &#9678 The physical volume is small, Weight is light &#9678 Dual-rate remote control via spare servo channel &#9678 4 CH setting by VR1 when Gain channel not connected &#9678 Reverse setting via Dial on Gyro &#9678 Gain Dial on Gyro used as Limit setting when Gain Channel connected Mechanical Installation&#653 06 &#652881&#65289 Mount Gyro on the helicopter. Mount sideways so that Label is facing Left, Right, Forwards or Backwards of helicopter. DO NOT install with Label facing Up or Down. &#652882&#65289 Do not install in the gyro near the muffler of a Nitro Helicopter. Avoid direct heat from Engine or Muffler to Gyro. &#652883&#65289 Connector mode&#65306 Step A&#65306Rudder servo connects to Gyro Step B&#65306Insert GY292&#652933 Pin connector to receiver (FUTABA is CH4&#65292JR is RUDD) &#12290 Step C&#65306Insert GY292 , GAIN 1 Pin connector to the receiver&#65292FU TABA is 5CH, JR is AUX2 or AUX3&#65292 Connect to receiver sensitivity switching channel&#12290 &#652884&#65289 Gain Plug should be connected so that single wire is connected to the servo signal pin. Set-up and installation of Gyro using gain Channel connected (6Ch Setup) &#652881&#65289 For Safety Reasons, Disconnect Motor of Helicopter during Installation and test. &#652882&#65289 Turn on the power to Transmitter &#652883&#65289 Set Gyro Gain on Tx to 40% initially for each direction of Channel switch for Gyro Gain on Tx (Using Endpoint/ATV mode initially) &#652884&#65289 Set Helicopter Tx setting to Heading Hold Mode (If Known) &#652885&#65289 Turn on the power to the Helicopter &#652886&#65289 Turn on the power of receiver on the Helicopter. Before Gyro LED light turns red, do not move Gyro and helicopter (about 7 seconds),This will influence the set-up. &#652887&#65289 Gyro MUST initialize in Heading Hold mode, not Rate Mode, If Light flashes 4 times a second, That indicated Gyro is initializing in Rate mode and will not continue until you switch to Heading Hold Mode. If so, switch to Heading Hold mode and Gyro will finish initializing. &#652888&#65289 Use the Gain dial on the Gyro as a Servo Limit adjustment. Set Gyro gain channel switch on Tx to Rate mode. While moving the tail still full left and right, adjust the gain/limit dial on the Gyro so that the tail slider on the Helicopter does hit either far end and bind. Light Table&#65306 Light Display GY292 Status LED ON Enters to lock a mode LED OFF Entering th...